Conjugated turbulent heat transfer with axial conduction in wall and convection boundary conditions in a parallel-plate channel

The steady-state conjugated turbulent heat transfer with axial conduction in the wall and convection boundary conditions is solved with the generalized integral transform technique for the flow of Newtonian fluid in parallel-plate duct. A lumped wall model that neglects transverse temperature gradients in the solid but that takes into account the axial heat conduction along the wall is adopted. Highly accurate results are presented for the fluid bulk and wall temperatures and Nusselt number. The effects of the conjugation parameter, Biot number, and the dimensionless channel length on Nusselt number and fluid bulk and wall temperatures are systematically investigated.     

宽电压范围下阳极氧化制备TiO_2纳米管阵列及其热稳定性

采用电化学阳极氧化技术,以含有NH4F和H2O的甘油溶液为电解液,在宽氧化电压范围(20~100V)下于纯钛表面制备了结构高度有序的TiO2纳米管阵列。利用扫描电子显微镜(SEM)考察了阳极氧化工艺(氧化电压、NH4F浓度、环境温度、水分含量等因素)及退火处理对纳米管形貌的影响;采用X射线衍射分析(XRD)表征了不同氧化电压和退火前后TiO2纳米管阵列的物相;并从电流-时间曲线出发简要地分析了纳米管阵列的形成机理。结果表明,纳米管的内外径和管长随氧化电压的增大而增大;NH4F浓度和环境温度对纳米管形貌有一定的影响;水分含量的多寡决定了能否在高电压下自组装形成纳米管阵列;TiO2纳米管阵列具有良好的热稳定性,管状形貌可以保持到700℃;直接制备的TiO2纳米管阵列均为无定型结构,经450℃退火处理后,无定型的TiO2纳米管转变为锐钛矿相,而600℃退火处理后,部分锐钛矿相转变为金红石相。     

高掺杂Ce,Gd(Y_(3-x-y)Ce_xGd_y)Al_5O_(12)荧光粉的发光下降及温度猝灭特性

采用高温固相法分别合成了不同Ce浓度掺杂的和固定Ce浓度为0.06不同Gd浓度掺杂的Y3Al5O12(YAG)系列荧光粉,通过测量其激发、发射光谱、漫反射光谱、荧光寿命和变温发射光谱,研究了掺杂元素的浓度对荧光粉发光性能的影响以及荧光粉发光的温度猝灭性质。研究结果表明:荧光粉发光强度随着Ce3+掺杂浓度和Gd3+掺杂浓度的提高均呈下降趋势。分析发现,荧光粉发光强度下降并非主要由浓度猝灭所引起,而是由于高浓度掺杂下发生YAG基质与Ce3+对激发光的竞争吸收,导致Ce3+对激发光的吸收量减少,从而影响发光强度。温度实验表明,随着温度的升高,荧光粉发光强度下降。Ce含量的改变对YAG:Ce荧光粉的热猝灭性质影响较小,Gd的掺杂使荧光粉的发射波长向长波方向移动,同时热猝灭现象严重。     

草酸铜原位催化高氯酸铵热分解的研究

通过TG-DTA-MS联用技术研究了草酸铜对高氯酸铵的催化过程。研究发现,草酸铜分解生成的氧化铜对高氯酸铵有较强的催化作用,添加2%的草酸铜使高氯酸铵的高温分解温度提前112℃。分解的气相产物主要有H2O,NH3,O2,HCl,Cl2,HNO,NO,N2O和NO2。在草酸铜原位分解生成的CuO表面吸附生成氧的过氧化离子(O2-)和氧离子(O-,O2-)是加速AP热分解反应的主要原因。     

一维链状锰配位聚合物[Mn(1,5-nds)(Him)_4]_n的合成、晶体结构及热稳定性研究(英文)

The synthesis,structural characterization and thermal behavior of a novel one-dimensional manganese (Ⅱ) complex of formula [Mn(1,5-nds)(Him)4]n [1,5-nds=naphthalene-1,5-disulfonate,Him=imidazole] is reported.The complex crystallizes in the triclinic system,space group P1,with a=0.835 42(13) nm,b=0.983 45(18) nm,c= 0.987 42(19) nm,α=60.523 0(10)°,β=97.748(2)°,γ=87.189(2)° and Z=2.The 1,5-nds ligand assumes the μ2 coordination mode and interlinks Mn(Ⅱ) ions into infinite one-dimensional chain structure along [111] direction,with the adjacent Mn…Mn distance being 1.144 99(12) nm.The chains are assembled into a three-dimensional supramolecular architecture via hydrogen bonds and C-H…π interactions.IR spectra and thermal analysis data are in agreement with the crystal structure.     

新型膨胀阻燃剂的合成及其在涤纶织物中的应用

氧氯化磷与季戊四醇反应制得双氯螺磷(2);2与三乙醇胺反应合成了新聚合物1,其结构与性能经1H NMR,IR,TG和SEM表征。研究结果表明,1自身具有很好的成炭性,对涤纶织物具有很好的阻燃效果,扩展了涤纶的分解温度范围;通过SEM对经1整理的织物残炭形貌进行分析,证实1是膨胀型的阻燃剂。     

Experimental study on equilibrium deviations in atmospheric pressure argon/helium surface wave discharges

Atmospheric pressure surface wave discharges generated with Ar–He mixtures with He concentrations up to 99% were studied using spectroscopic techniques. The variation of electron density and linear power density with He concentration and along the plasma column is discussed together with the excitation temperatures derived from the Boltzmann plot of the excited states of Ar I and the values of the b(p) parameters to derive the thermodynamic equilibrium state of the discharge. Important deviations with respect to Local Thermodynamic Equilibrium were observed for He concentrations over 50% as the discharge shifts from a recombining to an ionizing behaviour. Furthermore, the discharge kinetic variations behind these changes are discussed.     

Analysis of relaxing laser-induced plasmas by absorption spectroscopy: Toward a new quantitative diagnostic technique

Broad-band near UV absorption spectroscopy was used to analyze atmospheric laser-induced plasmas formed on metallic and refractory targets. When the common emission spectroscopy only provides the density of the radiating atomic excited states, the technique reported in this paper is able to achieve high spatial resolution in the measurement of absolute number densities in expanding laser-induced plasmas. The reliability and the versatility of this technique, which is based on the comparison between results of the numerical integration of the radiative transfer equation and experimental spectra, were tested on different targets. The evolutions in time and space of the absolute population of the plasma species originating from metallic alloys (Al–Mg and Cu–Ni) and refractory materials (C/SiC) were achieved over large time scales. Owing to its accuracy, this absorption technique (that we call “LIPAS” for Laser Induced Plasma Absorption Spectroscopy) should bring a new and enhanced support to the validation of collisional-radiative models attempting to provide reliable evolutions of laser-induced plasmas.     

On the stoichiometry of mass transfer from solid to plasma during pulsed laser ablation of brass

We have performed spectroscopic analysis of the plasma produced by pulsed laser ablation of brass in a low pressure argon atmosphere. The intensities of several spectral lines of copper, zinc and lead were measured for succeeding laser pulses applied to the same irradiation site. The intensities and spectral shapes of the observed transitions were compared to the spectral radiance computed for plasma in local thermal equilibrium. At a delay of 600 ns after the laser pulse, the plasma is characterized by typical values of temperature and electron density of 1.1 × 10⁴ K and 1.2 × 10¹⁷ cm^− 3, respectively, and an elemental composition equal to that of the sample. Small changes of spectral line intensities were observed with increasing number of applied laser pulses. They were attributed to the alteration of the plume expansion dynamics as a consequence of crater formation on the sample surface. The results indicate that the mass transfer from the solid to the plasma is stoichiometric.     

Thermal cured epoxy resins using certain calixarenes and their esterified derivatives as curing agents

The acetyl esterified calixarene (CA) derivatives were prepared from calix[4]resorcinarene (CRA), and p‐tert‐butylcalixarene (BCA[n], n = 4, 6, 8), respectively. Using these CA derivatives as curing agents, the thermal curing reactions of two multifunctional epoxy resins (jER 828, 186 g/equiv., and ESCN, 193.7 g/equiv.) were investigated. The temperatures of glass transition (T_g) and decomposition (T) were measured by DSC and TGA, respectively. Based on the yields, T_gs, and T_ds of the thermal cured jER 828 epoxy resin with CRA‐E100, the curing conditions were optimized to be tetrabutylphosphonium bromide (TBPB) as catalyst in NMP at 160 °C for 15 h. Under this curing condition, the cured materials of jER 828 or ESCN using various CA derivatives as curing agents were prepared. Except for BCA4 derivatives, the yields of thermal curing reaction were higher than 90%. T_gs and Ts of the resultant cured materials were in the range of 113–248 °C and 363–404 °C, respectively. These results mean that the cured epoxy resins with excellent T_gs were successfully formed by using CA derivatives as curing agents. It was also found that the T_gs of cured epoxy resins were strongly affected by the degree of esterification of CA derivatives. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1931–1942, 2010